icon pumpМы предлагаем Вам пищевые насосы собственного производства и производства фирмы Sivag Pumps (Австрия), для перекачки по трубам шоколада и других вязких пищевых продуктов с температурой от минус 60 до плюс 300о С и давлением до 16 bar, с рубашкой водного обогрева и без рубашки обогрева.

GENERAL INFORMATION

SIVAG Pumpen Ges.m.b.H. is primarily concerned with manufacturing and distributing of pumps for many years. Basically the products are used for industrial purposes. Since 1989 the head office of SIVAG Pumpen has been in Hollabrunn. The support for national and international customers is raised without any distributors or sales organisations directly from SIVAG – Hollabrunn.

THE BUSINESS STRATEGY IS CONCENTRATED ON:

  • Customer- and target oriented solutions on unbureaucratic way in cooperative collaboration
  • Best price/performance ratio
  • Competent contact persons and high qualified technical personal
  • Short delivery times in consequence of transparent and accurate business processes

THE PRODUCT RANGE CONTAINS PUMPS FOR:
1

  • Chemicals
  • Clean water
  • Foods
  • Viscous fluids
  • Waste water

 2014-08-12 17292014-08-12 17302014-08-12 1731

VOLUTE CASING PUMP NC ACC. EN 228582

Horizontal single-stage volute casing pumps, with bearing bracket. Nominal duty points and main dimensions in accordance with DIN 24256 – EN 22858. Single-stage volute casing pumps of series “NC” are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids.

FEATURES

  • Maximum nominal pressure: 16 bar
  • Temperature: up to 260°C

MATERIALS

  • Volute casing pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special material combinations are produced on request.
  • Shaft sealing alternative with mechanical seal or stuffing box. The materials and the execution of the mechanical seal and the packing in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS3

  • Capacity: up to 1100 m³/h
  • Discharge head: up to 158 m W.S.
  • Connections: from DN 32 to DN 300
  • Motor rotation speed: 1450 min-1 and 2900 min-1

GENERAL PERFORMANCE CURVE

4

VOLUTE CASING PUMP IN BLOC DESIGN NCB5

Close coupled horizontal single-stage volute casing pumps, with IEC-norm electric motor. Single-stage volte casing pumps of series “NCB” are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids.

FEATURES

  • Maximum nominal pressure: 16 bar
  • Temperature: up to 180°C

MATERIALS

  • Volute casing pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special material combinations are produced on request.
  • Shaft sealing alternative with mechanical seal or stuffing box. The materials and the execution of the mechanical seal and the packing in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 500 m³/h
  • Discharge head: up to 158 m W.S.
  • Connections: from DN 32 to DN 200
  • Motor rotation speed: 1450 min-1 and 2900 min-1

GENERAL PERFORMANCE CURVE

6

SELF-PRIMING CENTRIFUGAL PUMP S7

Self-priming centrifugal pumps with open impeller are used for pumping liquids containing solids up to 80 mm diameter and for abrasive liquids. The special design makes the “S” series a quick self-priming pump.

FEATURES

  • Maximum nominal pressure: 16 bar
  • Self-priming up to 8-9 m H2O

MATERIALS

  • Self-priming pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special materials are produced on request.
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 1500 m³/h
  • Discharge head: up to 70 m H2O
  • Connections: from DN40 to DN300

PERFORMANCES

2014-08-12 1751

SELF-PRIMING INTERNAL GEAR PUMP R9

The self-priming internal gear pumps of series “R” are positive displacement rotary pumps. The capacity is directly proportional to the rotation speed. This pump is available as bare shaft pump with bearing bracket.

FEATURES

  • Maximum nominal pressure: 16 bar
  • Temperature: -60°C to +300°C

MATERIALS

  • Internal gear pumps are made of stainless steel 1.4408 (AISI 316), cast iron EN-GJL-250 and nodular cast iron EN-GJS-400. Special materials are produced on request.
  • Shaft sealing alternative with mechanical seal, stuffing box or magnetic drive. The materials and the execution of the mechanical seal, packing or magnetic drive in accordance to the liquid.

TECHNICAL CHARACTERISTICS10

  • Capacity: up to 350 m³/h
  • Viscosity: up to 100.000 mm²/s (cSt)
  • Connections from DN 40 to DN 250

PERFORMANCES2014-08-12 1800

LOBE PUMP B11

Lobe pumps of series “B” are positive displacement rotary pumps. The capacity is directly proportional to the rotation speed. Two synchronously driven rotors are rotating in a casing. This construction provides a very gentle pumping of fluids.

FEATURES

  • Maximum working pressure: 10 (20) bar
  • Temperature: up to 180°C

MATERIALS

  • All hydraulic parts are made of stainless steel AISI 316. The gear box is made in cast iron EN-GJL-250. Special alloys and surface hardenings are available on request.
  • Shaft sealing alternative with mechanical seal, stuffing box or special lip seal. The materials and the execution of the mechanical seal, packing or lip seal in accordance to the liquid.

TECHNICAL CHARACTERISTICS12

  • Capacity: up to 300 m³/h
  • Viscosity: up to 100.000 mm²/s (cSt)
  • Connections from DN25 to DN200

PERFORMANCES

2014-08-12 1805

STAINLESS STEEL CENTRIFUGAL PUMP 3S ACC. EN 73313

Horizontal single-stage volute casing pumps in stainless steel with dimensions and performances acc. EN 733. The “3S”-series is a close coupled execution with standard IEC-norm electric motor. These pumps are used for pumping clean and low contaminated liquids (also used for various chemicals).

FEATURES

  • Maximum nominal pressure: 10 bar
  • Temperature: -20°C to +120°C

MATERIALS

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304) and 1.4571 (AISI 316).
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS14

  • Capacity: up to 240 m³/h
  • Discharge head: up to 90 m W.S.
  • Connections from DN 32 to DN 100
  • Motor rotation speed: 1450 min-1 and 2900 min-1
CURVES 2900 MIN-1  CURVES 1450 MIN-1
 15  16

CENTRIFUGAL PUMP IN STAINLESS STEEL CD_2CD17

Close coupled horizontal pumps in single-stage (CD) or two impeller (2CD) execution in stainless steel with electric motor with extended shaft directly connected to the pump. The centrifugal pumps “CD” and “2CD” are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids.

FEATURES

  • Maximum nominal pressure: 8 bar
  • Temperature: -5°C to +120°C

MATERIALS

  • Centrifugal pumps are only made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS18

  • Capacity: up to 15 m³/h
  • Discharge head: up to 70 m W.S.
  • Connections from G1“ to G1 ½“
  • Motor rotation speed: 2900 min-1
CURVES CD CURVES 2CD
 19  20

CENTRIFUGAL PUMP IN STAINLESS STEEL DWO21

Horizontal single-stage centrifugal pump with open impeller in stainless steel with electric motor with extended shaft directly connected to the pump. Centrifugal pumps of series “DWO” are used for pumping clean and contaminated liquids without abrasive components.

FEATURES

  • Maximum nominal pressure: 8 bar
  • Temperature: -5°C to +110°C

MATERIALS

  • Centrifugal pumps are only made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS22

  • Capacity: up to 65 m³/h
  • Discharge head: up to 18 m W.S.
  • Connections from G2“ to G2 ½“
  • Motor rotation speed: 2900 min-1

CURVES

23

SUBMERSIBLE PUMP DG24

Submersible pumps series “DG” with vortex-impeller with wide flow, for pumping all kinds of waste water, sewage and sludge. The vortex-impeller grants pumping fluids containing solids up to 150 mm diameter.

FEATURES

  • Maximum nominal pressure: 6 bar
  • Temperature: up to +40°C

MATERIALS

  • Pumps are made of cast iron, stainless steel AISI 316 and bronze. Special materials are produced on request.
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 380 m³/h
  • Discharge head: up to 23 m W.S.
  • Connections from G1 ½“ to DN 150“
  • Motor rotation speed: 960 min-1, 1450 min-1 and 2900 min-125

GENERAL PERFORMANCE CURVE

26

27

SUBMERSIBLE PUMP DR28

Submersible pumps series “DR” with open multi-channel impeller for pumping clean and waste water, with solids contaminated sewage and sludge. This kind of impeller grants pumping fluids containing solids up to 120 mm diameter. 

FEATURES

  • Maximum nominal pressure: 6 bar
  • Temperature: up to +40°C

MATERIALS

  • Pumps are made of cast iron, stainless steel AISI 316 and bronze. Special materials are produced on request.
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARATERISTICS

  • Capacity: up to 500 m³/h
  • Discharge head: up to 52 m W.S.
  • Connections from G1 ¼“ to DN 150
  • Motor rotation speed: 960 min-1, 1450 min-1 and 2900 min-129

GENERAL PERFORMANCE CURVE

30

31

SUBMERSIBLE PUMP GR32

Submersible pumps series “GR” with open multi-channel impeller and cutting system. This kind of pumps with special impeller and grinder system is used for pumping waste water with long fibers and cutting able solids.

FEATURES

  • Maximum nominal pressure: 6 bar
  • Temperature: up to +40°C

MATERIALS

  • Pumps are only made in cast iron.
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 110 m³/h
  • Discharge head: up to 54 m W.S.
  • Connections from G1 ½“ to DN 100
  • Motor rotation speed: 1450 min-1 and 2900 min-1

GENERAL PERFORMANCE CURVE

33

34

SUBMERSIBLE PUMP AP35

Submersible pumps series “AP” with open multi-channel high head impeller. This kind of pumps with special impeller is designed for high delivery heads. They are used for pumping clean and waste water and low contaminated liquids with small solids.

FEATURES 

  • Maximum nominal pressure: 8 bar
  • Temperature: up to +50°C

MATERIALS

  • Pumps are only made in cast iron.
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 42 m³/h
  • Discharge head: up to 60 m W.S.
  • Connections from G1 ½“ to G2“
  • Motor rotation speed: 2900 min-1

GENERAL PERFORMANCE CURVE

3637

3839

CENTRIFUGAL PUMP FOR CHEMICALS TMR_ZMR40

Close coupled horizontal single-stage centrifugal pumps with standard IEC-norm electric motor. This centrifugal pumps series “TMR” and “ZMR” is used for pumping clean liquids (mainly Chemicals). Shaft sealing is available with mechanical seal or magnetic drive.

FEATURES

  • Maximum nominal pressure: 8 bar
  • Temperature: -20°C to +100°C

MATERIALS

  • Centrifugal pumps are made of PP (glass fiber reinforced Polypropylene) or E-CTFE (Etylene- Chloro TrifluoroPolyetylene carbon fibers filled / PVDF-similar).
  • Shaft sealing is available with mechanical seal or magnetic coupling. Pump execution and materials, mechanical seals and bushings in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 55 m³/h
  • Discharge head: up to 40 m W.S.
  • Connections from DN 40 to DN 50
  • Motor rotation speed: 2900 min-1

GENERAL PERFORMANCE CURVE

41

CENTRIFUGAL PUMP FOR CHEMICALS ZGE ACC. EN 2285842

Horizontal single-stage volute casing pumps, with bearing bracket. Nominal duty points and main dimensions in accordance with EN 22858. Single-stage volute casing pumps of series “ZGE” are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids.

FEATURES

  • Maximum nominal pressure: 16 bar
  • Temperature: -40°C to +120°C

MATERIALS

  • Centrifugal pumps are made of PP (Polypropylene), PE (Polyethylene), PVDF (Polyvinilidene Fluoride) or PVC (polyvinyl chloride).
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 1700 m³/h
  • Discharge head: up to 155 m W.S.
  • Connections from DN 32 to DN 300
  • Motor rotation speed: 1450 min-1 and 2900 min-1
 CURVE 2900 MIN-1 CURVE 1450 MIN-1
 43  44

CHEMICAL VERTICAL SUMP PUMP KGK45

The vertical sump pumps series “KGK” are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids. They have column and volute casing submerged, own mechanical support and motor mounted above the liquid to be pumped.

FEATURES

  • Maximum immersion depth: 4 m
  • Temperature: -10°C to +40°C

MATERIALS

  • Centrifugal pumps are made of PP (glass fiber reinforced Polypropylene) and PVDF (Polyvinilidene Fluoride).
  • Pump execution and materials and bushings in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 270 m³/h
  • Discharge head: up to 85 m W.S.
  • Connections from DN 25 to DN 100
  • Motor rotation speed: 1450 min-1 and 2900 min-1
CURVE 2900 MIN-1 CURVE 1450 MIN-1
 46  47

AIR OPERATED DOUBLE DIAPHRAGM PUMP DDA48

The air operated double diaphragm pumps of series “DDA” are used for pumping a variety of different liquids (mainly chemicals), without abrasive, coarse or extended solids. These pumps can be installed submerged in the pumped liquid. The DDA-pumps are self-priming. And they can be used for thin and viscose fluids.

FEATURES

  • Maximum suction head: 6 m
  • Temperature: -10°C to +40°C

MATERIALS

  • The air operated double diaphragm pumps are made of PP (glass fiber reinforced Polypropylene), PVDF, carbon fiber filled PVDF, Aluminium, stainless steel AISI 316 (AISI 316 polished – FDA).
  • Pump execution and materials, diaphragms and valves in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

  • Capacity: up to 40 m³/h
  • Discharge head: up to 70 m W.S.
  • Connections from G ¼“ to G2“

 49

IMPELLER PUMP EP50

The special construction of impeller pumps provides a very gentle pumping of fluids. The flexible impeller grants pumping thin and high viscose liquids (up to 50.000 cP). The impeller pump is self- priming up to 6 m and can be used in both directions.

FEATURES

  • Maximum nominal pressure: 4 bar
  • Temperature: up to +100°C

MATERIALS

  • Impeller pumps are made in stainless steel AISI 304 and AISI 316.
  • Shaft sealing with mechanical seal. Materials of mechanical seal and impeller in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS51

  • Capacity: up to 45 m³/h
  • Discharge head: up to 30 m W.S.
  • Connections from ¾“ to DN 100
  • Motor rotation speed: 470 min-1 to 1400 min-1

GENERAL PERFORMANCE CURVE

52

SELF-PRIMING LIQUID RING PUMP EP53

The liquid ring pumps are used for pumping clean fluids without solids up to viscosity of 100 cP. The special construction of the pump casing grants that the pump is self-priming and can be used in both directions.

FEATURES

Maximum nominal pressure: 6 bar

Temperature: up to +100°C

MATERIALS

Liquid ring pumps are made in stainless steel AISI 316 and bronze.

Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

TECHNICAL CHARACTERISTICS

Capacity: up to 30 m³/h

Discharge head: up to 40 m W.S.

Connections from ¾“ to DN 65

Motor rotation speed: 1400 min-1 to 2800 min-1

GENERAL PERFORMANCE CURVE

54